RX WELD Argon Regulator for MIG TIG Weld, CGA580, 6.6FT Hose

I’m not speaking as an experienced welder, but more of a weekend hobbies. The value for the money on this gauge, I think is really good. Gauge did not leak at all and fit perfectly. It also fit nicely with my 80 CF tank that I purchased from a local supplier and it looks great and fits my welding cart perfectly. With all the fittings that they send I was able to fit this to my welding outfit with no problem.

Gage was as described and worked perfectly with no leaks. At a very fair.

I'm not a pro welder. If you're looking for such opinions, skip mine. I'm a home-jobber, hobby-welder. I needed a flow meter to get my mig setup to do aluminum wire. This flow meter attached just fine to my argon bottle, no issues. The hose it came with is fine too. I detected no leaks once it was all snugged up (I just used soapy water spray). I have no way to test if the flow-rate I'm setting is accurate. I used settings I found on-line (~15 to 20 ft/min), did my aluminum migging and the parts were joined. My welds don't look great, but it worked... my destructive testing tells me the welds are at least as strong as the base metal (aluminum angle). What I could notice was I didn't get the ugly porosity that low/no shielding gas would show. So, as far as I know, the flow-meter is passing out enough gas to do the job. Maybe its too much?.. no idea. More may be a waste than 'the right amount', but the welds are cleaner than if it was too low. I tested the low/no shielding gas use-case just so I could see what it looks like... and its very ugly. Look online for pics/vids of bad shielding on aluminum welds... its unmistakable when you see it. Now, when I say 'ugly', I mean beyond the clumpy, uneven welds a home-jobber like me puts down... b/c my welds are 'ugly'. I don't stack dimes,... I may lay down a dime, then a quarter, then a nickel... repeatedly. Bad form, bad movement control, all the wrong stuff. So, what I mean is, the low-shielding-gas issues present as pits/pot-holes and dirty/dark spots in the weld... that would make even an otherwise pro-welder's nice 'dime-stack' look like a pitted, dusky looking mess. Once you've seen it, you know what to look for. Despite my good results, I'd say that any pro is not going to use or trust this 'cheap' meter, nor should they. If your welding is mission-critical and/or lives are on the line, use the good stuff... and any pro welder knows that anyway. If you're like me and just need to stick some metal together for small projects where if they fail no one dies?.. then perhaps this flow-meter is just fine for you as well.

Well made for the price. I don't use it as often as a welder would in a business. Easy to read and adjust flow for my purpose. The hose connections worked without any added fittings ( may be different for your setup). Quality is good for a non name brand.

Every fast delivery and good quality

Great for infrequent use, if you just need a regulator

75%argone 25%co2 welding with a mig welder

Worked good excellent price

This is a good quality product at a great price. Comes with adaptors to install different ways as required

Whilst the regulator comes with a gas line it has completely wrong fitting attached. You do get a single female coupling and a poor quality hose clamp- you have to cut you gas line . Also the flow meter (floating ball) has Argon and CO2 scale. Not sure on accuracy and male cone fittings are nor rubber nut machined brass. Not exact mating to cylinder outlets so care and check for leaks regularly- additionally the main fitting to the bottle is a USA NPT thread and does not fit Australia BSP gas bottle threads. - whilst you can change the nit - the added cost and messing around- not worth the headache. Do not buy for Australia

So far seems really good quality , haven't used it yet will update if any issues

Ordered the regulator flowmeter kit along with the hose. The regulator and flowmeter look reasonable quality. The supplied hose also looks reasonable quality with crimped male fittings at each end. The issue I have is the hose fittings are too big for the supplied regulator connection. The regulator comes with a loose hose connection, so in order to get this to work, I would have to cut off one of the hose crimped connections, then fit the supplied hose connection with jubilee clamp. The reason I purchased the regulator kit with hose was to have proper crimped connections that should last longer then my old pushfit connectors. Sent back for refund.

Clean, well package, well made